We use cookies - Our website uses cookies to provide you with a better experience as well as for analytical purposes. For more information on our privacy practices and cookie policy please read our Privacy Policy.
Vision TC-HDMIIPTX/3 HDMI over IP transmitter (receiver sold separately) - Distributes HDMI via a network, H.265 compression, One-to-One directly over a LAN or directly, One-to-Many over LAN, IR Pass-through, USB 1.1 transmission
The TC-HDMIIP/3 converts HDMI signal into TCP/IP packets for transmission over a standard LAN network. With no visible loss of video quality it is perfect for corporate and digital signage applications.
Beware of cheap alternatives that flood your network!
It can support USB version 1.1 from the transmitter to all receivers. Each receiver has two USB ports for adding flexibility. This is for USB peripherals like keyboard, mice, but not applications that demand high bandwidth like interactive displays.
Transmitters and receivers sold separately so you can scale your system.
A reset button restores EDID to default, or for advanced applications holding either of the reset buttons down will copy the display EDID to the transmitter.
Need to display one source on many screens? This product multi-casts, so you can have one transmitter for the source, and over 100 x receivers can sit on the network – one for each display. Only one transmitter per network.
Connect one transmitter directly to a receiver and completely bypass a network. This will work with a standard CAT6 cable up to 150 m (492 ft) on a high quality cable.
When using a LAN the signal will be repeated by each node on the network, resulting in unlimited length.
Fully HDCP 1.4 compliant, it supports resolutions up to 1920 x 1200 @ 60 Hz.
Digital audio which is encoded on the HDMI signal is transmitted.
Control the source device from the display with the IR pass-through. An IR blaster and receiver cable is included, and it supports standard 20-60 kHz IR signals.
EDID (extended display identification data) is automatically passed through. Just connect everything together and it will work immediately.
Video is compressed using the H.265 protocol. Images are full colour with smooth motion.
Despite using the standard IP protocols you don’t need to be a network engineer. All end points must be on the same subnet… that’s all you need to know. For best results use a stand-alone network for this system.
This product requires a power supply for each transmitter and receiver. It does not use PoE.
Many video-over-IP solutions require a managed switch so that IGMP snooping can be enabled, but in this case no advanced switch setup is required. A low cost unmanaged switch can be used.
If you need more than one source to be distributed over one physical LAN you can use Virtual LANs to separate the topologies. The systems are kept separate and cannot be used as a matrix. A DHCP switch assigns IP addresses to each end point and is used to create the vLANs.
If the input is shut off the display will be allowed to go to sleep.
This version uses a Sigmastar chipset and is not compatible with the previous v2 product which uses a HiSilicon chipset.
92 x 67 x 168 mm (length x width x height)
150 x 135 x 70mm
1.26 kg (per Tx or Rx)
0.15 kg
Metal
Black
H.265
HiSilicon
CAT5E/6 Shielded or Unshielded
1.3 (3D not supported)
1.4
150 m
HD 1920×1200 @60Hz
6.75 Gbps
RGB, YCbCr 4:4:4, YCbCr 4:2:2
12-bit
LPCM 2.0CH, 32 kHz, 44.1 kHz, 48 kHz
20 Hz ~ 60 kHz
Human body model —±8kV (Air-gap discharge) & ±4kV (Contact discharge)
10℃ - 50 ℃ / 14 °F - 122 °F
20~90% RH (non-condensing)
1.5 Watts
Input:
1 x HDMI (type A)
1 x USB (type B)
Outputs:
1 x RJ45
1 x 3.5mm Minijack (for IR blaster)
100-240v 50/60Hz AC 5 volt / 1 amp
Transformer integrated into plug
Interchangeable UK/EU/US/AU
1.5m
41.3 x 40.2 x 28.4mm
1 x IR Blaster with 1.5 m Cable
1 x set of wall mounting ears
Lifetime return-to-base
Dimensions | 92 x 67 x 168 mm (length x width x height) |
---|---|
Colour | Black |
Weight (kg) | 0.150000 |
Warranty | Lifetime return-to-base |
EAN | 6862537000007 |
>